I have my Oxford grips wired to an Eastern Beaver fuse box, but this video shows where the plug is.I have a 2017 non-ES bike and I have fitted Oxford heated grips and they work well. I use the Oxford controller and mine are wired into the battery, however, I seem to recall reading on here that the Oxford grips can be wired into the Yamaha connectors on the right hand side of the bike as you sit on it. I haven’t been able to find the post covering this and I have just read through all 11 pages of this thread.
I have a couple of questions, if I can connect to the Yamaha connectors, then do I still use the Oxford controller or will connecting to the wiring loom activate the grip control in the menu? I am guessing the Yamaha loom will give a switched live? If anyone reading this has connected Oxford grips to the Yamaha connectors, then can you either post some pictures or give me a link to the posts that do? Thanks in advance for any help and advice.
Okay, just realized I never added the link! Super Tenere Eastern Beaver Install Part 1 - YouTubeMymate charlie sent pics of his and I’m all sorted now
FYI: Apply liberal amounts of grease to the portion of the harness inside the throttle housing, this seems to be a common wear point, eventually causing failure due to shorted/broken wire.Nice one T4ten, confirms my clip is about right.
Yes, all greased up, thanks.FYI: Apply liberal amounts of grease to the portion of the harness inside the throttle housing, this seems to be a common wear point, eventually causing failure due to shorted/broken wire.
See pictures of the Installation Instructions on page 2 in this thread, Reply #24 - Heated grips. | Page 2 | Yamaha Super Tenere Forumanyone have heated grip installation instructions for a non -ES 13'? I picked up the heated grips kit off Ebay but would like to know if there are instructions out there for me to follow. Thanks
I have 2018 ze/es and these were the ones I fitted:good day, is 2HS-H29A0-V0 heated grips compatible with 2019 model? if so, does the settings/power on and power for the heated grip automatically show up under the menu?
thanksI have 2018 ze/es and these were the ones I fitted:
Heated Grips (Super Tenere)
£304.00
Part Number: 2BS-829A0-00-00 Yamaha
Not sure what model you have or where you are so I suppose that might influence the part number.
I can confirm that once installed these automatically show up in the menu. Hope that helps.
Guys and Girls
I have an issue with my OEM heated grips on my 2015 Super T ES.
I lose the heated grips display intermittently. (Now it’s completely missing) I noticed it in the spring, but only now, in the fall decided to try to take care of this issue after reading the thread here.
At first, I ohmed out the right grey connector and it was completely open. The left black one read 2.4Ω.
I was happy that I only need to buy the right grip. Before putting things together again and after looking at the wires on the grip side (looks good) I decided to spray electric contact cleaner, loosen the zip ties, and shake the wires a bit. Used my voltmeter to check for ohms again and this time around I get the following.
I still don’t see the display of the heated grips.
- Left Black reads 2.4Ω. Spec from shop manual 1.21-1.48 Ω
- Right grey reads 1.8Ω. Spec from shop manual 1.17-1.43 Ω
I didn’t think that out of spec ohm readings would be the issue. I thought I would get a complete open.
Maybe I didn’t get a good reading first time around, but now I definitely do.
What are your thoughts?
Thank you,
Late reply but compressed air from a basketball inflation needle push in under grip from outside and blast air, Grip moves anywhere you want it .FYI,
I finally got to doing this. Back in October I couldn't even find any on the market, and the winters here are long.
Bottom line, I had to replace both. I measured 1.5 ohms on the new ones.
The work was more hassle than I thought, especially getting the left grip off, obviously no issues with the right side.
Thanks for the help.