Search results

Question is kinda right there. I have most cables plugged in but display was crushed when bike was totaled. I want to start this thing. I cleaned out tank without the float going back in. The tilt sensor is in the up position. All kick stands up in nuetral. Not seeing/hearing fuel pump run...

Just need it for troubleshooting.

HYDRAULIC UNIT <<2013+ ES and non ES 23P-85930-19-00 vs HYDRAULIC UNIT<<2012 23P-85930-09-00 I want to pull the one off my 2012 and put on 2015 I think it will work. Anyone know for sure?

Never seen this before. One pipes?

As it says

Wrecked rear or engine blown gen1 forks gauge pod wheel bars and wiring and mirrors May even need a tank with title a plus

that is Slavage1 the box I parts bike. I just took it for a spin. Quieter and smoother than my 2018

I have a solid abs orange light as if the abs is ready to initialize waiting on emitter pulses. Tried the procedure to read any fault codes 63 00 so none there. Put in the paperclip did not get pulsing ABS light << I think this is the key to the issue. Did the codes delete / reset. Went...

Looks like dot 4 changed opten is better than going to the 5.1 Any thoughts?

Any tricks to getting those ahole footlong rubbers to stick in the groove without glue or messing them up factory ones appear dry. 1 is under air filter other is around edge of top cover. Thanks

Opinion? There are 2 ports on the airbox one is for valve cover breathing Other port looks to be a drain but my 2017 has a rubber plug with a tension hose clamp and the 2018 has just the open hole. On a good note I see no dust or signs of violation. But it has low miles. On dirt bikes the have...

I have done the initial 14FT-LBS in sequence. Do I go to 22FTlb and verify the angle or do I do the 22ft lbs and then the Angle torque? It appears to be a 3 step with the angle last but presents it as a 2 stage process. Can someone that has done this chime in please? Using lubed NEW Head Bolts...

Not sure if because I have been on the bmw a bunch but took the s10 out today. As I went down the driveway, I let off the throttle and lightly made sure it was closed by nature. The engine seemed to stick at high idle. After going only around the block it seemed to continue this. Felt like a...

Team Tenere, Bought the parts bike and started pulling motor. Exhaust was the most brutal to remove, This was a Northern Jersey / NY bike but I can see this happening to anyone. Once I broke off the studs the exhaust was bonded to the head. PB Blaster and some heat and some banging and wiggling...

Making an attempt to figure out all the connections to see if bike is salvageable. Bought the parts bike here in sale section from Gonzo . (great guy) I decided that since it looks like all parts are there to just see if it will boot up with no real error codes then pull head and or engine...

Need one.. Thanks JR I have dealt with 3 members here purchasing and am solid no bs no scam buyer,

Is the a lujgage rack for s10 that uses the same mounting and lock system as the new gsa? I would like to use same boxes on both bikes. I am wondering if they can be flip mounted since exhaust is opposite on thes bikes? Any Pannier Jugglers out there? I am looking for a rack that will allow...

I have a low mileage 2018 7k. I am very sure the basket springs are loose or at least 1 is loose causing noise in low rpms and no load conditions. It is annoying. It there a fix to shim springs or maybe a recommended replacement basket non OEM or is a new basket the only fix? Thanks

Problem is: menu jumps whenever I pull the clutch in all the way. Got to thinking there is no electrical sensor on the clutch why does it cause the menus to cycle. I put my index finger on the menu button and pull in the clutch..... The clutch lever is hitting the button... gotta set the...

Had the bike fall off the lift after my attempts to tie it without hurting the grips , tank, or shrouds. Nothing workied. So I put some eye-bolts(stainless) on the motor plate. They work amazingly! The plate is a little non symmetrical so I pick the spots based on interference points and...