Search results

Try this http://www.yamahasupertenere.com/index.php?topic=18097.0

WYSIWYG $35 shipped CONUS Paypal gift Pls reply by PM Thanks. Jim a.k.a Gonzodog

Sold

BTW this manual is for Gen 1 Super Teneres. Lets sweeten the deal. Have a NIB air filter. Will throw in as a bonus. How can you resist? ::015::

Slightly used and a few smudges but perfectly useable. Lots of great information. $50 shipped CONUS Paypal gift Thanks for looking Gonz

While riding on the James Bay road, the final drive on my 2013 S10 started dripping. Luckily I noticed it in Matagami prior to heading towards Radisson ( 600+km with virtually no services for a moto). Called ahead to HarricanaAventures in Amos (180 kM south of Matagami). Parts Manager David...

::012:: After another 1,000 miles on the S10 after the RRR install I can say I am totally satisfied. Robust design Great fit and finish Lots of adjustability I still haven't changed the position since the initial installation. I did spend a fair amount of time getting the bars where I wanted...

Have had Gen 1 on my '13 for a few weeks now and I am very pleased with the result. Had to install longer brake/clutch hoses (PITA$$) and rearrange the throttle cable guide. Once that was done, the risers were easy to adjust. I have not moved hem from the first position I came up with. Not...

Re: Rox risers Extension not needed with this set. To go further up and back would require longer brake & clutch hoses, at least for my '13.

SOLD These are the black powder coated nerf bars. Nothing wrong with them, I am just moving in a different direction. http://www.happy-trail.com/find-your-bike/yamaha/xt1200z-tenere/nerf-engine-guard-super-tenere.html $175 + actual shipping seems fair.

SOLD These are the up 1.25" and back 1" risers. linky: https://www.rockymountainatvmc.com/p/1316/27440/Rox-Speed-FX-Pro-Offset-Elite-Block-Risers?term=rox+risers This set was used for two seasons, rode coast to coast, and is in near new condition. I use anti-seize on all steel-to-aluminum...

I pull the clutch lever assembly apart once a year to give a lube job. First time I used white lithium spray grease. It dried out pretty quickly. Lately I have been using very thick red grease that holds up better to rain, etc. Shift lever pivot is another to keep an eye on. I saw someone...

I received the new bar risers for my '13 from Gordon yesterday. All I can say is WOW, these are super robust. As far as I am aware there is nothing on the market that comes close. Installation instructions make the install a 10 minute job. Have not had a chance to ride yet and plan to order...

Like my '13 a lot. Most comfy street bike I have had. But compared to my '04 FJR, it is just butt ugly. However, I can't see it when I'm riding it so looks are definitely not a problem. ::022::

Re: RRR Adjustable Handlebar Risers for the Super Tenere? Need Inputs - Interested

Finally completed the Rostra install today. Holds speed very well under load +\- 1 mph. Definitely works best in 6th gear. For some reason, riding local roads, remembering to shift up into 6th is something I tend to neglect. Tends to hunt a little on down slopes but it is acceptable. I set...

Better to remove the damper hub and dampers and leave them at home to prevent them from going missing during the change at the tire shop. Good tip on the axle from the punkin side.

Guys, I'm a little confused with wiring in the 250-3592 (lighted control pad with engaged light). Do I need to get another 5 pole relay to wire the engaged light? It seems that the directions I have are in conflict. Per Supercruise's write up the 5 pole relay is wired as: 87 not used 87A...

Could be interested. Sent you a PM

Re: FS: Skid Plate Pm sent