Search results

O2 sensor? I have my ecm flashed so it does not use the o2 sensors Why would then set it up that the oil holes line up for when it is on side stand? Thats a bit weird

Im looking at this skid plate. So it does not fit correctly with arrow headers and stock center stand? How hard to modify to fit? Oil drain holes dont line up?

I get all the other steps. Just trying to clarify what exactly you do with CCT. you push chain guard until it hits the cam chain tightener. The instructions nor are any of the videos i watched clear. I under stand all the other steps like K up , T up rotate 271, 72, 360, etc......, shim up...

when you put the cams back in, do you just align chain with paint marks and put tensioner back and it should be at the correct tension? I know there is a bunch more detail as to removing connectors, wiring, oiling etc.... Just the manual does not seem very specific when it comes to what you do...

I'm thinking of tackling a valve clearance inspection. I'm unclear what needs to be done with the cam chain tensioner. My interpretations is if the clearances are good, nothing. if i need to remove the cams to adjust, i need to loosen the cam chain tensioner?? I saw online video that someone...

I saw this code posted elsewhere in the forum in reference to a valve inspection. THe post mentioned that this job should be 2.2 hours? Where can i find a list of job codes to confirm this? And if presented to service dealer should they stay within this- time/billing?

Anyone know if these should work? They appear to just replace existing halogen no new caps or canbur decoders or whatever just plug on as if an oem halogen https://www.amazon.ca/H7-Headlight-Non-Polarity-Conversion-Required/dp/B0BS8M8WZD/ref=cm_cr_arp_mb_bdcrb_top?ie=UTF8 AHREN H7 LED...

Did they work?

Yes those bulbs I understand 168 194 2835 t10 are all the same size

I want to replace these with led. The oem are very yellow compared to headlight Can I get any t10 or 2835 led bulb? Does it have to be under a certain wattage? Some are 5w some 3.8

I never use it. But if there was a short that is why it would not allow cruise to set. Very strange that it would have a short. It is way under air box does not get exposed

Finally fixed it Turns out the grip cancel switch had a short in it. Replaced it, cruise now working.

When you are at speed when cc stays lit. Im wondering what it means when flashing on power on.

I finally received my grip cancel switch replacement since I was not sure if the old one was faulty because I got sporadic continuity when testing. I replaced Ed now when checking diagnostic 82 and I push throttle back it goes from off to on Now when I turn on not start and press the cruise...

2020. And i brought it in for Front brake switch recall. Still no change, CC won't set.

So are you saying that it is unlikely the flash impacted Cruise control unless they copied a Flash file from a non CC bike? So as long as they selected the correct model of bike, it accounts for cruise control?

Where can i find details on what parts of a flash impact Cruise control? Like a diagram or something? I know cruise can be impacted by a lot of things. Clutch switch, ABS wheel sensors, brake switch (front and rear), Throttle position, ....... But I've read that an ECU can impact Cruise...

I spoke to person who flashed. Yes they are aware of my model and that it has cruise. But they said they don't touch anything that would impact cruise? I had it flashed prior to me installing Arrow headers myself since it was going to be quite some time before i would receive them. Here is a...

my rear brake does not flicker at all. I ride often in groups with me leading, and everyone has said it only comes on when slowing or stopping.

Thank you so much for the response. Very frustrating trying to find the solution. Here are my results 20 Works. off, then ON 21 OFF when transmission is in gear and clutch pulled 80 works OFF then ON 81 works OFF then ON 82 Is ON 83 is OFF and when brakes are pressed, it GOES ON If I'm...