Search results

I have the rear seat,grab bars,handlebars, exhaust, & windscreen (however it was trimmed down 4 inches). I have always used full syn Mobile 1 oil/gear diff lube with mobile 1 filter changed every 5000 miles valves were in spec at 24000. I have not replaced the CCT however it has only been heard...

2016 Bump!

Price drop with a bump.

2012 Tenere original owner bike located in Las Vegas NV 38000 miles black with red. ECU Reflashed Leo Vince slip on pipe K&N filter V-Stream windshield Pro Taper "Raptor" handlebars Michelin PS3 tires Stomp tank pads and have stock exhaust, handlebars, and cut down and trimmed windscreen...

No issue mounting at all with stock lines but you will need to find a way to thread the ends for the bar end to bolt up. I used a nut that would barely fit in the end of the handle bar it needed to be hammered in with a mallet. You can also use some type of spanner bolt you can purchase for...

i would not worry about it to much and just ride! I have ran my S10 through a full tank of gas multiple times at those speeds. My header pipe looks the same as yours and have a carbon Leo pipe with 26000 miles. Plugs looked fine at 24000 miles and she never burns any oil. Other then getting...

I think the bike tops at around an actual 130MPH.I have read 140MPH o the speedo with no luggage and 4 inches cut from the top of the stock screen.

You can take the speaker apart and solder them yourself. If you have not purchased yet then order the unit along with Torx speakers from Rocket Moto(highly recommended) he will have them soldered to the unit before sending it to you.

Those do look good on the Tenere and I have been thinking of grabbing a set cause they are a bargain. Have either of you layed the bike over to test them yet?

Awesome rode I hit it every trip down to Cali now and on the way up north through Big Sir. On the raising the forks I elected to raise the rear an inch with ADV dog bones, made a great improvement and added some ground clearance as well. No issues with stability all the up to 140 on the speedo :)

The Mobile One filter m-108 is 2.5 inches same as the stock Yamaha along with a few others on Dallera's tech post. I believe he actually measured aftermarket oil filters and posted the lengths of them all for everyone but the K&N looks a little long due to the nut on the end and comes out to be...

I would try just moving the grips and controls inboard first and test ride for awhile before cutting them cause once you commit there is no turning back :)

I drilled mine as well and was very easy to do without any problems. I have removed the pin on other bikes and hated it when the clamp shell would move on me so that is what made me decice to drill mine.

Try the Pro Taper "Raptor" bars. they mount with the stock lines no problem, are taller, and less back sweep to them. You will need to modify the ends for the brush gaurds but not a big deal.

Are you riding around in Tmode? I have a hard time believing that it is hard to pass anything with the Torq curve of the S10. I leave mine in 6th and pin the throttle ::26:: by the time I pass a semi truck I am well over a hundred MPH. You might need a Hyabusa.

Also stand behind Motoport 100% for a custom taylored fit as well as any option you would like to add. Pricey but well worth it in my opinion because skin is not replacable.The Mesh fabric will flow more air then the stretch but it is a little abrasive if its rubbing or contacting any painted...

I just ordered an ACD last week and it has already shipped, arrived, and is installed on the bike ;) I did try to originally order a raw one but Cedric quickly emailed me that day and advised that it would be a few weeks before a raw was finished, however I was able to choose either the black or...

Why not just raise the rear an inch(100 bucks) and lower the triples on the forks(for free). The stock size front with a good street touring tire and the bike will easily drag hard parts, even without lowering the front any. JMHO

I changed my rear Pr3 Trail at 10,000 miles and they were just getting to the wear bar in the middle and a little squared from freeway commuting 160 miles weekly. I prob could have squeezed another 1000 miles before a bald center on the rear tire. The front is still mounted and at 12,000 miles...

The sweep and angle of the stock bars did not feel right for myself. I bolted on the Pro Taper "Raptor" bars and could not be happier! Around an inch taller, along with a straighter angle, feels much better to me and when standing they are just about right. Try adjusting the stock bars around...