Recent content by NJGreg

  1. NJGreg

    Y.E.S. Extended Warranty

    Couple few posts above Clicky
  2. NJGreg

    Top cases with a passenger

    I think you'll get tons of answers which will mostly be different from each other. Will have a lot to do with the actual set up. This week I switched out my givi mounting plate for a givi universal one which is roughly 1.5" lower and 2" more rearward giving the wife more usable seat moving her...
  3. NJGreg

    Whos selling the spoke kits?

    LadleSport has kits.
  4. NJGreg

    To lightbar or not to lightbar that is the question.

    I just used the stock rigid brackets to the holes that are there. I did grind a litte off the side at the ends of the brckets for better fitment.
  5. NJGreg

    To lightbar or not to lightbar that is the question.

    Go for it. I threw a rigid in there and turns night into day. I wired mine up to the high beam switch with a toggle so I can choose to run it with high beams or high beams only.
  6. NJGreg

    Michelin Road 6 pulls to the left

    Final update. RMATV is doing a warranty return on the front. Didn't say anything about the rear nor did I ask. Doesn't seem to be a ton of choices out there with availability. I'm just gonna run the dunlop roadsmart3 front with the road6 rear. Did a 100 mile ride saturday and they seemed to...
  7. NJGreg

    Michelin Road 6 pulls to the left

    Update, Ordered a new front roadsmart3, got it spooned on and the hard left pull went away. Let go of the bars and goes straight on down the road. Got a warranty email in with dealer, waiting to see whats gonna happen.
  8. NJGreg

    Michelin Road 6 pulls to the left

    I mounted up a set or road 6's and am having a hard left pull, bike dives if you let go of the bars. Loosened both axles and retorqued in sequence to spec, pull is still there. production dates of 3122 front, 3222 rear. Purchased like two weeks ago from rmatv. Any solution ever come out of this?
  9. NJGreg

    Rear LED Tail/Brake Light Wires

    You probably done figured it out, but being there are no blinkers in that light no need for digital flasher so should be good to go. I tapped the wires for my top box into the harness under the passenger seat and ran it out from there. My set up is only brake and blinkers.
  10. NJGreg

    HARD START

    For me, I had gotten fuel about a week prior and not from a budget station. Later attempts to start a week later had temps around 60F
  11. NJGreg

    HARD START

    I may as well in here also. 2021 model 9600 miles. I do believe I cycled the ignition switch several times as I had installed a fuse box under the seat and tested stuff out. Had a hard start took me over a week to get figure out/get going. Would not start after sitting for a week in the cold...
  12. NJGreg

    SPOKES !!! any alternative?

    @Ladlesport has repair sets in their store
  13. NJGreg

    Corbin seat, what am I doing wrong?

    Sorry for late response. I'm only at 8k miles so no long term thoughts, but corbin vs stock is night and day difference. Stock seat I would get restless after 45-60 minutes. I'm at 5'11" 230'ish lbs, 31.5ish" inseam, and have it in the high position. Can't flat foot it, but I can reach bottom...
  14. NJGreg

    Show Us Your Panniers

    Another one who opted for the Mosko's with mototrek's racks. Once mototrek releases their own hard cases I will order a set of those as they will be using mosko's mounting system. Stuffed them full of towels to see if they got in the way of the wife sitting on the seat,,we good to go.
  15. NJGreg

    Corbin seat, what am I doing wrong?

    Revisited this today in 100+ heat after taking the seats off to wire in some extra rear signals from my top box. I found that the latch you transfer over form your stock pan is to far forward. The bolt location in corbins pan is to far forward. I drilled out my latch bracket to a couple sizes...
Top