Homemade Top Case quick release

RCinNC

Well-Known Member
Joined
Aug 30, 2014
Messages
2,816
Location
North Carolina
I was asked about this in another thread by a member; I didn't want to hijack the other thread, so I'm posting this here.

The top case quick release was designed in conjunction with a homemade luggage rack, so they would work as a system. The system was designed around a bicycle seatpost quick release. This is just a cam lever that you push to create tension that holds a bicycle seatpost in a seatpost tube after you adjust it. Normally the quick release is a round clamp that works a lot like a hose clamp. I got rid of the round clamp portion and just used the clamping lever, shaft, and retaining nut.



There's an "L" shaped bracket on the rear of the topcase, and another one on the rear of the luggage rack. The topcase bracket has an open ended slot that allows it to slip over the quick release shaft. Once the brackets are lined up, you just push down the quick release and it locks the rear of the topcase to the luggage rack. The extra holes on those "L" shaped brackets are so you can run either a cable lock or a padlock through them and lock the topcase to the luggage rack. The brackets are just made from standard hardware store aluminum angle, cut out with hacksaws and/or a sabresaw and then shaped with a coping saw and a coarse wood blade, and hand files.



This is the quick release lever in the open position. Lifting the lever releases the tension that holds the bracket on the topcase to the bracket on the luggage rack.
The three big flat washers are there to spread the load out across the topcase bracket to provide more clamping force.



This is the topcase being lifted off the rack after the quick release lever has been released.



This shows the threaded shaft from the quick release passing through the rear bracket on the luggage rack. You can't see it in the photos, but there's a knurled nut at the end of the threaded shaft. Turning the nut increases or decreased the tension on the quick release. It doesn't require any tools to adjust it, the nut is tensioned by hand.



This is what locks the front of the topcase to the luggage rack. Those two front blocks on the underside of the topcase slide down through corresponding slots in the luggage rack. Once they slide down through the slots, you push the case forward, which pushes the lips on the clamping blocks under the luggage rack, effectively trapping the front of the case so it can't be lifted off. The blocks are spaced to hug that center rail of the luggage rack, so the topcase can't move from side to side. The clamping blocks were formed from pieces of 1/4" ABS sheet plastic, laminated together. The lips are formed from small pieces of aluminum bar stock; I think it's 3/16". For the blocks to work correctly, there has to be just enough clearance for the lips to slide under the luggage rack, or else the case will be loose in the front.





Additional close up photos of the blocks.



This is the attachement plate for the topcase. All the hardware related to the quick release system is attached to this plate alone; this was done so the plate, with all the hardware, could be easily removed from one case and put on another case without having to remeasure everything.
 

RCinNC

Well-Known Member
Joined
Aug 30, 2014
Messages
2,816
Location
North Carolina
I wish I had the tools to make stuff like that. Very nice!
Thanks! Actually, my tool collection isn't that extensive. They're mainly hand tools: saws, files, a small tap and tie set, etc. The only power tools I use are a drill, a sabresaw, a Dremel tool and a handheld grinder. I don't own any bench tools, not even a drill press.
 

Checkswrecks

Ungenear to broked stuff
Staff member
Global Moderator
2011 Site Supporter
Joined
Mar 7, 2011
Messages
11,489
Location
Damascus, MD
Excellent idea - Thanks for sharing and hope you don't mind if I borrow some of it.

Are the side holes for a padlock, snap clip, or some other secondary means of retention?
 

RCinNC

Well-Known Member
Joined
Aug 30, 2014
Messages
2,816
Location
North Carolina
Excellent ! About how many miles with it mounted ?
A little less than 57,000 miles at this point, from Maine to Utah, with a lot of off pavement like Shafer Canyon and Phantom Canyon Rd. That case doesn't come loose unless I want it to.

Message sent from a motel in Mississippi...me and the case are heading to the Gulf Coast! :cool:
 

RCinNC

Well-Known Member
Joined
Aug 30, 2014
Messages
2,816
Location
North Carolina
Excellent idea - Thanks for sharing and hope you don't mind if I borrow some of it.

Are the side holes for a padlock, snap clip, or some other secondary means of retention?
I don't mind at all...in fact, no BS, I'm honored. That's pretty much why I post these things. I benefitted from seeing what other fabricators did, so this is my "paying it forward". I can honestly say that the bicycle seat clamp might be a unique method of attachment;. I've never seen it anywhere, and it came to me because I ride bikes.

Yes, those side holes are there for either a padlock or a cable lock. Mainly to defeat the casual thief. The cable lock works best, since I can lock the case shut and lock it to the rack with one lock.

The open ended slots are bungee attachment points.
 

Cycledude

Well-Known Member
Joined
Jan 29, 2016
Messages
3,997
Location
Rib lake wi
A little less than 57,000 miles at this point, from Maine to Utah, with a lot of off pavement like Shafer Canyon and Phantom Canyon Rd. That case doesn't come loose unless I want it to.

Message sent from a motel in Mississippi...me and the case are heading to the Gulf Coast! :cool:
Well I will have to say it has been VERY WELL tested !!!
 

toypro1

New Member
Joined
Nov 4, 2014
Messages
29
Location
East central Illinois
I don't mind at all...in fact, no BS, I'm honored. That's pretty much why I post these things. I benefitted from seeing what other fabricators did, so this is my "paying it forward". I can honestly say that the bicycle seat clamp might be a unique method of attachment;. I've never seen it anywhere, and it came to me because I ride bikes.

Yes, those side holes are there for either a padlock or a cable lock. Mainly to defeat the casual thief. The cable lock works best, since I can lock the case shut and lock it to the rack with one lock.

The open ended slots are bungee attachment points.
Good job - thanks for sharing
 

Mikecmp

Member
Joined
Mar 20, 2016
Messages
54
Location
Chardon, oh
Very cool. I will say your design is loads better than the very poorly designed Givi monokey setup my top box uses in conjunction with my altrider plate. There was like 1/4 play between the two, that you were supposed to take up with rubber bumpers. Riding off road those bumpers got squishe fat, then the “dinging” started. The box would bounce between the rack and the catch holding it on.

I got so fed up with it I drilled two holes in the bottom of the case and bolted it on. Makes no sound now. Why Givi and their engineers couldn’t come up with something elegant like your solution is beyond me.

In shirt, nice job!

Mike
 
Top