GPS windshield crossbar mount suggestions?

JT3NSB

Active Member
Joined
Jan 25, 2023
Messages
66
Location
NC
I have a Garmin zumo 396 mounted on a ram mount on my bars. I just put a Madstad shield on and I would like to move my GPS off the bars to this cross bar. I have enough wire, just need a good mount suggestion? A ram type deal would make it too tall and in my sight line. I’m hoping for just a simple bracket? I’m searching mounts but can’t find what I’m lookin for…

You guys have been offering great suggestions as I sort out my new 23… Thank you !
403C3B80-CA3F-4CAD-84F8-3DCBD5A8B289.jpegCCC2BE33-FA81-4903-B9DE-39D1DFF7C00B.jpeg
 

thughes317

Well-Known Member
Joined
May 27, 2018
Messages
1,055
Location
The Bluegrass, KY
Why not mount the ball on the far laft/right side of the bar and use your existing arm and mount to center the GPS?

hack drawing, viewed from above:

hackdrawing.png
 

Muybig

Active Member
Joined
Aug 16, 2021
Messages
233
Location
Montreal
JT read the Motopumps product description - it has a safety mechanism against robbery I just ordered one for my New Zumo XT
 

whisperquiet

Well-Known Member
Joined
Feb 20, 2011
Messages
728
Location
Southern Illinois
Last edited:

Quisp

New Member
Joined
Jan 26, 2023
Messages
6
Location
Davenport,Fl

audiowize

Active Member
Joined
Sep 29, 2022
Messages
215
Location
Seattle
I have that eBay mount on my Guzzi 1200 Sport and it works perfectly. I opted for the Altrider mount on the S10.
 

Checkswrecks

Ungenear to broked stuff
Staff member
Global Moderator
2011 Site Supporter
Joined
Mar 7, 2011
Messages
11,489
Location
Damascus, MD
Thread moved.
Please start threads in an appropriate sub-forum. thx

The mods
 

RCinNC

Well-Known Member
Joined
Aug 30, 2014
Messages
2,816
Location
North Carolina
I recently got a Zumo XT, and it's kind of a beefy unit. I wanted a mount that would really grab the accessory rail without putting all the pressure in one single spot. The mount that came with the unit only had a single u-bolt style mount, and the u-bolt is way bigger than it needed to be for the half inch rail. More surface area to grab a hold of makes for a tighter grip with less pressure put on the rail (you could probably put a dent in the rail if you really tightened down a single u-bolt). So, I made my own base mount for the RAM armature that came with the Zumo.

I bought a couple half inch 1/4-20 u-bolts at the hardware store, along with some 1/4-20 acorn nuts. In order to increase the surface area for gripping, I made a couple bushings for the inside of the u-bolt out of some scraps of ABS plastic. This is what the u-bolts looked like:




The base for the mount was made out of a scrap piece of 5/32 aluminum. I drilled four holes for the u-bolts, and tapped a hole in the center of the aluminum plate for a 1/4-20 threaded RAM ball I bought on Amazon. I spread some JB Weld on the threads and screwed the RAM ball into the mount; it's now permanently attached.

Here's that part of the mount:



I made a bushing for the underside of the plate, again to add more gripping power to the mount. The bushing is made from a bunch of pieces of scrap ABS sheet plastic. I drilled a half inch hole in the pieces, glued them all together, then cut off a small section to form the bushing. I glued the bushing to the plate with JB Weld.

Here's what the bushing looks like:



Here's the finished mount:



....and on the accessory rail:



Here's the Zumo XT mount attached to the rail mount with the RAM armature:



I wanted to keep the Zumo power cable out of the way to minimize the chance of it getting snagged on something, so I made a little cable attachment plate to bolt to the rail mount. It was made from a scrap piece of 1.5mm aluminum, and it fits over the ends of one of the u-bolts. I made a little cable clamp out of a scrap piece of ABS plastic; this fits over the Zumo power cable and is secured to the plate with a couple of 6-32 screws that fit into a couple tapped holes in the 1.5mm plate. For the portion of the cable that's exposed before it goes under the cowling, I ran it through a section of clear vinyl tubing for a little extra protection. The power cable is routed down to a PC-8 under the seat.

Here's the mount with the cable attachment plate:



It required very little tightening of the acorn nuts to get a really strong grip on the rail.
 
Top