Recent content by offcamber

  1. offcamber

    Cam Chain Tensioner replacement ?

    I know this has been discussed but I can't seem to find a tutorial specific the the S10 on how to JUST change the cam chain tensioner. At some point I will tackle a valve check but for now all I want to do is put in the upgraded tensioner. Even the service manual isn't clear on how to change it...
  2. offcamber

    Stumble and check engine light..no throttle.

    Update on the S10.... Its not the TPS or Accelerator sensor. I humbly have to admit I read the test wrong and when I understood what it said the part is fine... That being said....I found the issue or at least I know roughly the cause. Its the MC Cruise aftermarket Cruise Control. Its either...
  3. offcamber

    Stumble and check engine light..no throttle.

    I think I figured it out...Accelerator position sensor when tested shows no change in resistance.
  4. offcamber

    Stumble and check engine light..no throttle.

    Found that although I am not sure what I'm looking at. Manual says the code will show after the engine is shut down but the key is still on. Showed 59. TPS
  5. offcamber

    Stumble and check engine light..no throttle.

    Showing error code 59 which I believe is TPS or its harness. Oddly enough I installed a MC Cruise about a year and half ago. I wonder if something has chaffed or come loose. Time to pull the tank and the airbox :(
  6. offcamber

    Stumble and check engine light..no throttle.

    No recent washes...fuel was put in about a week ago and run 100 miles since. I need to figure out how to get the codes without a diagnostic reader.
  7. offcamber

    Stumble and check engine light..no throttle.

    2012 with about 26K on it. No issues till this morning. Started fine. Blipped the throttle and it stumbled and the check engine light came on...no throttle response at all. Turned it off and restarted fine. Revved it and it seemed okay. Took off for work and it was fine until I got to the...
  8. offcamber

    Novasight and extended covers?

    Its PETG....not great but we'll see how it holds up. Should be good up to about 170F I can print ABS I just don't have an enclosure. You can anneal PLA and it increase the temp resistance quiet a bit. Almost to ABS temps.
  9. offcamber

    Novasight and extended covers?

    I guess I'll see if I can tweak the design a little. Its not my model but I can modify it.
  10. offcamber

    Novasight and extended covers?

    THese https://www.amazon.com/gp/product/B07D91KCPK/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1
  11. offcamber

    Novasight and extended covers?

    I installed the Novasight H7 bulbs and 3D printed my own caps but the caps hit the forks near full lock. Am I the only one experiencing this? I can't see making them any shorter or the bulbs won't fit.
  12. offcamber

    Mosko Moto Reckless 80 Liter System

    Is that the R80 Revolver without the side bags?
  13. offcamber

    Mosko Moto Reckless 80 Liter System

    That explains the fit, When I installed my V2 I tried it both ways and it defiantly fit better with the handles off. Its not a big deal to remove them and they would serve no purpose when the R80 is on anyway. Since I run hard panniers most of the time and swap the R80 on for trips its simple...
  14. offcamber

    Mosko Moto Reckless 80 Liter System

    It looks like you removed Looks like you removed the rear grab handles? Is that correct?
  15. offcamber

    MC Cruise issue

    I have used it for short trips. This week was suppose to be the big trip to VA which has since been cancelled due to covid. It has worked flawlessly since I got the replacement unit. My only regret is not buying it sooner.
Top